2008 HOBBY STOCK RULES –BOONE COUNTY RACEWAY INC. 1-13-2008
SAFETY EQUIPMENT: Rules apply at all times car is on track. Snell-rated SA 2000 or SA2005 helmet required. SA95 no longer allowed. Roll bar padding required in driver compartment (Fire retardant recommended). SFI-approved full fire suit, fire retardant neck brace, gloves and shoes required. Recommended: Fire retardant head sock and underwear; head and neck restraints; collapsible steering shaft. Driver-side window net required, minimum 16” x 20” ribbon or mesh style, and must be mounted so latch is at top front of window. Minimum three-inch wide SFI. approved five point safety belt assembly required, (Y-type shoulder harness not allowed), must be mounted securely to roll cage, recommended to be no more than one year old. Kill switch required within easy reach of driver and must be clearly marked “OFF” and “ON”.
FRAME: Any American OEM full body rear wheel drive passenger car, 1964 or newer, full frame or unibody. Frame must match body. Minimum 107.5 inch wheelbase, maximum one inch difference from side to side. Rear of frame behind rear tires, from a point no further forward than one inch behind factory seam, may be replaced in OEM location with tow inch by three inch steel tubing with .095 inch wall thickness, same length as material removed. Factory seam must remain visible. Unibodies must tie rear frame to front frame. Frames may be “X” braced. No Camaros, Firebirds, or Mustangs.
ROLL CAGE: Main cage must consist of continuous hoops, minimum 1.75 inch O.D. tubing, with a wall thickness of at least .095 inch, low carbon or mild steel recommended. Four-post roll cage required, front down bars and rear
hoop must be welded to OEM frame. Driver’s head must not protrude outside cage with helmet on. Rear hoop must have “X” brace, consisting of one full horizontal and one full diagonal bar, minimum 1.25 inch O.D. and .083 inch wall thickness. Front down bars must be tied together, passenger side front down bars must be maximum 11 inches in from top of door. Must be minimum 40 inches between front and rear down bars at top of door panel. Maximum 41 inches from top center of windshield to front edge of rear hoop; maximum 13 inches to front edge of top halo. Top halo must be minimum 40 inches across, outside to outside. Rear hoop may be maximum 12 inches in from bottom of opera window. Minimum one cross bar in top halo. May have maximum two horizontal bars (in addition to bar tying front frame horns together) for radiator protection; must be behind bumper, within confines of body, no wider than OEM frame horns. Rear kickers (down bars) and engine hoop required, and must be minimum 1.25 inch tubing with .083 inch wall thickness. Fuel cell protection required, must be mounted frame rail to frame rail, no higher than fuel cell, inside trunk area with maximum 1.75 inch tubing. All bars must be inside body.
DOOR BARS: All door bars and uprights must be minimum 1.75 inch O.D. and .095 inch wall thickness. Minimum three door bars, both sides, parallel to ground, and perpendicular to driver. Minimum four uprights tied from frame to top door bar on driver side, and minimum three uprights on passenger side. Steel door plates, 18 gauge or .049 inch minimum thickness, must be securely welded to outside of door bars on driver’s side. Plate must cover area from top door bar to rocker panel and from rear down post to five inches in front of seat. Must be visible for inspection.
BODY: All bodies must be unaltered OEM in OEM
location and match frame. Front body
mounts must be visible.
Sunroofs and T-tops must be enclosed. Aftermarket plastic nose pieces are allowed, recommended to match body. No spoilers, hood scoops, ground effects or skirting altering OEM appearance. Unaltered OEM steel hood and trunk only, no gutting. Hood and trunk must be securely fastened and back of hood must be sealed off from driver compartment with metal. Hood must be separate from fenders. Front inner wheel wells may be removed, rear wheel wells may be removed to middle seam. Trunk floor directly over rear end housing must be removed. No overlapping or shortening of body panels. All glass must be removed, all windows in body must remain open; maximum seven-inch metal sun visor allowed across top of windshield opening. All doors must be securely fastened. Fenders and quarter panels may be trimmed for tire clearance, ONLY. No reflective body panels.
2008 HOBBY STOCK RULES (PAGE 2)
DRIVER COMPARTMENT: Minimum three windshield bars in front of driver. Aluminum high-back seat only, bolted to roll cage. Driver seat may be no further back than rear edge of B-pillar. Driver must be sealed off from track, driveline, engine and fuel cell. Dash not to extend more than 24 inches back from center of lower windshield opening. Dash must be flat, rear can be no higher than front, except for cowl in front of driver. No other interior tin or covers. Inside rear quarter panels, below window level, may be cut out. Doors may be gutted. No cutting out of firewalls, roof, floor, kick panels, rocker panels, or trunk floor, except for roll cage clearance. All holes in firewalls and floor must be covered with metal. Rear firewall and speaker deck must be metal and be of OEM design for that make and model. No mirrors or reflective sun visors.
FRONT SUSPENSION: All components and mounts must be steel,
unaltered OEM, in OEM location and match frame. OEM rubber A-frame bushings only. Bolt on spindle savers allowed.
No sway bars, spring spacers, chains or cables. Some exceptions are 1978—1987 GM mid
sized metric frame, OEM upper A-frame may be replaced using aftermarket upper
A-frame (Steel only). Bolt on spindle
savers allowed. Upper A-frame mount
must remain OEM and can’t be moved.
STEERING: All components must be steel unaltered OEM, in OEM location and match frame. OEM steering column may be replaced with steel steering shafts (collapsible steering shaft recommended). Steel knuckles only. No steering quickeners or remote power steering reservoirs. Steering wheel and quick release may be aluminum.
SHOCKS: One unaltered steel, non-adjustable, non-take apart, OEM-mount shock, in OEM location, per wheel. No coil-over shocks, air shocks, remote reservoir shocks. No Schrader or bladder type valve. No coil-over eliminators. Rear OEM shock location is 4.5 inches from bottom of housing to center of bolt hole, and centered on control arm bracket. $20 claim on any shock. One or all shocks on car may be claimed per event, counting as one claim on card, following shock claim procedures and penalties.
SPRINGS: One steel spring per wheel only in OEM location. All coil springs must be minimum 4.5 inches O.D. and non progressive.
REAR SUSPENSION: All components and mounts must be steel, unaltered, OEM, in OEM location and match frame. OEM rubber control arm bushings only. Center of rear lower control arm bolt hole must be 2.25 inches from bottom of housing. No independent rear suspension. No sway bars, panhard bars, spring spacers or rubbers, chains or cables.
REAR END: No floater rear ends. OEM or OEM replacement steel axles only. Nine-inch Ford rear end allowed, but must be mounted like OEM rear end (centered) for that make and model. No lightened ring gears. Must be welded spider gears, or mini spool. No torque dividing differentials.
BUMPERS/RUB RAILS: Bumpers must be approved OEM in OEM location, capped to fender with steel. Maximum one inch wide by two inch tall rub rails bolted flush to body from fender well and rear quarter panel. Lexan type also allowed. Front and rear tow hooks mandatory.
TIRES AND WHEELS: Unaltered OEM 205/75, or 205/70, 14 inch, or 15 inch passenger car tires only. All four tires must be same size. Tires must be inside body. No racing, snow, or all-terrain tires. No softening, conditioning, siping/grinding or grooving. Maximum seven inch wide, three to four inches offset, unaltered D.O.T. stamped steel wheels with standard bead dump – must weigh a minimum of 21 pounds. Reinforcing of stock wheels recommended. No wheel spacers. One inch O.D. steel lug nuts required. No bleeder valves.
BRAKES: Steel, unaltered OEM, or unaltered OEM replacement, operative four wheel, disc (front) and drum (rear) brakes, and must match frame. Master cylinder must be in OEM location. No antilock brake systems. No aftermarket brake pedal assemblies, brake shut-off or bias adjuster. Steel brake lines only, must be visible. Hubs/rotors, axle flanges and drums may be changed to different bolt patterns and larger studs.
EXHAUST: OEM cast iron exhaust manifolds only. No center dump type manifolds. Exhaust must extend past firewall and turn towards ground. Maximum 2 inch O.D. exhaust pipes. Must remain duel exhaust, no crossover or “Y” pipes. No exhaust sensors. Mufflers recommended.
2008 HOBBY STOCK RULES (PAGE 3)
FUEL SYSTEM: Mechanical push rod fuel pumps only. Unaltered OEM two barrel carburetor for that
engine, except: booster I.D. may be
machined to .250 inch and venture I.D. machined to 1.375 inch on Rochester
carb. Must remove carburetor choke
plate. No carb spacer. One .25 inch (maximum) thickness gasket
only. $50 cash claim on carburetor,
following carburetor claim procedures and penalties Air cleaner top/stud cannot direct air into carburetor. No top flow air cleaner housings, cold air
boxes or air cleaner duct work. Maximum
22-gallon racing fuel cell required, must be in minimum 18-gauge steel
container. Must be securely fastened in
truck above level of OEM trunk floor behind rear tires, no further forward
than factory seam where rear frame rail can be replaced by minimum of two
.125-inch thick, solid steel straps, two inches wide around entire cell. Metal firewall must be between driver and
fuel cell. No fuel cells allowed over rear end housing. All cell mounts
must be steel, securely welded to frame/cage.
No adjustable fuel mounts. Fuel
cell vents, including cap vent, must have check valves. Fuel lines through driver compartment must
run through metal pipe or metal conduit.
No fuel filters in driver compartment.
Limit of one fuel filter. No
cool cans. A flapper, spring or ball type filler rollover valve is required,
if fuel cell does not have aircraft style positive seal filler neck/cap system.
FUEL: Gasoline only, no ethanol. Pump grade recommended. No performance enhancing additives or scented additives. Fuel must pass both dialectric meter and chemical tests. Fuel sample may be taken from any car at any time. Penalty for illegal fuel is disqualification from event and $250 fine-first offense.
WEIGHT: No ballast allowed. Any item deemed as ballast will be required to be replaced, i.e. fuel cell straps, fuel cell cans, battery boxes, etc. No titanium, magnesium or carbon fiber products. No gun-drilled, tubular, hollow bolts or studs. Steel fasteners only.
BATTERY/STARTER: One 12-volt passenger car battery only, must be in marine-type case, securely mounted to frame or roll cage in metal frame behind seat or in trunk area. Starter must bolt in OEM location. Must have capability of starting without being pushed or pulled. Must leave initial staging area on demand, unaided, or go to rear of that race.
GAUGES/ELECTRONICS: No transmitting or listening devices, timing retard controls, or digital gauges (including tach)or cameras. No electronics monitoring, computer devices capable of storing or transmitting information except analog tach. No ignition control boxes, OEM ignition only, firing order cannot be changed. All ignition rotors, caps, coils and modules must remain OEM appearing. No alternators. No electronic traction control devices.
TRANSMISSION/DRIVE SHAFT: All forward and reverse gears must be operational.
MANUAL: Must be unaltered OEM three or four speed, with minimum 10.5 inch steel/organic single disc-type clutch and steel pressure plate assembly inside an explosion-proof bellhousing – minimum 270 degrees around top of clutch and flywheel area. No lightweight bellhousings. No hydraulic clutch release bearing. Steel unaltered flywheel only – 16 pound minimum - $150 fine if illegal.
AUTOMATIC: Must be unaltered OEM, with unaltered OEM pump, original bellhousing and minimum 10 inch diameter torque converter containing a minimum of three quarts of fluid - $150 fine – if illegal. Torque convertor must have a minimum .125 inch plug. Must be approved scattershield constructed of .125 inch by three inch steel, 270 degrees around flexplate. Flexplate must be full, unaltered OEM, or OEM replacement.
DRIVE SHAFT: Steel drive shaft (minimum 2.5 inch diameter) and slip-yokes only. Drive shaft must be painted white. 360 degree drive shaft loop required and must be constructed of minimum .25 inch by two inch solid steel, or one inch tubing, mounted six inches back from front U-joint.
ENGINE COMPARTMENT: Engine must be in OEM location, using any steel engine mounts (no mid-plate allowed), except Ford Metric frames must have back of fuel pump in front of crossmember, and crossmember may not be altered or moved. Also GM metric frame, center of fuel pump must be located minimum 1.75 inches in front of cross member measured at frame. Engine must be OEM appearing, must be able to be used in conventional passenger car without alteration, GM with GM, Ford with Ford, Chrysler with Chrysler. Minimum two-core steel or aluminum radiator. Steel or aluminum V-belt pulleys only. Overflow tubes must be directed to ground, between frame rails. Accumulators and Accusumps must be mounted under hood.
2008 HOBBY STOCK RULES (PAGE 4)
ENGINE SPECIFICATIONS: Any American make engine allowed. Steel heads, block and oil pan only. OEM passenger vehicle production block only. No GM Bowtie, Ford SVO or Chrysler W blocks. GM approved block numbers are: 3892657, 3914660, 3914678, 3932388, 3932386, 3956618, 3970000, 3970006, 3970010, 3970014, 10066033, 10066036, 10243880, 14010207, 14010209, 14010287, 14016376, 14016379, 10054727, 14088528, 14088548, 14088552, 14093638, 14101148. Stroke must match block. No 400 or larger cubic inch parts allowed. Maximum 361 cubic inches (GM); 363 cubic inches (Ford); 370 cubic inches (Chrysler). Maximum compression ratio is 9.0 to 1, no tolerance. Compression ratio checked using Whistler and cubic inches checked using pump, OR by visual inspection, such as part numbers, casting numbers and flat top or dish pistons (track option which method is used). Flat top or dish pistons only, no gas ported pistons. Cylinder heads must be unaltered approved OEM and minimum 76 cc combustion chamber. No Vortec heads, GM approved steel head numbers are – 14079267, 3986336, 3986339, 3986339X, 3986388, 3932441, 376445, 3928454, 3932454, 3876487, 3973487, 3973487X, 3973493, 3951598, 468642, 330862, 333882, 3998920, 3998991, 3998993, 3998997, 3970126; Ford – no after market or SVO heads; Chrysler – no after market or W-2 heads, 360 cubic inch heads only. Must have unaltered OEM cast iron two barrel intake. No hi-rise or marine intake manifolds. Flat tappet cam/lifters only. No mushroom lifters. Cannot alter lifter bores. No porting, polishing, or alterations of any kind to heads or intake, disqualifications and $250 fine if illegal. OEM non-roller rocker arm only. Guide plates and screw-in shouldered studs .375 inch max. allowed. No roller lifters, or stud girdles. “Wet” sump oiling system only. Studs may be pinned or use non-shouldered screw-in type. Poly locks allowed. OEM type harmonic balancer only and may not be altered. OEM type steel or aluminum water pumps only.
ENGINE CLAIM: $325 claim and exchange of engine. Wrecker will get $25 of this money for pulling the engine. You must be in lead lap and have a running motor to claim. Claim does not include the following: flywheel, clutch, pressure plate, bellhousing, breathers, carburetor, starter, motor mounts, oil/temperature sending units, fan and pulleys, clutch ball, clutch arm, throw out bearing, dip stick, water pump, fuel pump, rod and plate, distributor, plug wires, water outlet and restrictor, exhaust manifold and pipes. Also during the engine claim, exhaust manifold must be pulled to inspect heads, and one spark plug must be removed to check flat top or pistons prior to transfer of engine to claiming driver. If, at this time, engine is found illegal, claimed driver is disqualified and suspended from all events until such time as a $250 fine is paid, for first offense. A $500 fine will be for the second offense and/or suspension. Claimer will then have the option to accept or decline the claimed engine. If declined, claim is not charged against him/her.
EIRI: (Except In Rare Instances) Decisions of officials are final and binding without exception. In some cases, track safety rules may take precedence over rules. Any discrepancy between class and track rules should be brought to the attention of the promoter or official.